Motorola Profile "e"nhanced Cellular Telephone
(170-1249) Programming
1 . . 2 . . 3 Simple Programming
Before you start, write down your cellular phone number here:
(_ _ _) _ _ _ - _ _ _ _ ,
and your Carrier System ID * (a 1 to 5-digit number) here: _ _ _ _ _ .
* Contact your Cellular Service Provider to confirm your Carrier System
ID Number.
TO ENTER PHONE DISPLAYS
1. Enter Programming [7], [4], [6], [6], [3], [#], EntEr and nuMbEr
Mode [FCN], [FCN]
(Hint: Spells P-H-O-N-E-[#],
[FCN], [FCN].
2. Enter Phone Number Enter Entire Phone Number (123) 555 - 1212
(_ _ _) _ _ _ - _ _ _ _ (sample phone
number)
Press [STO] EntEr and SyS id
3. Enter the System Enter System ID _ _ _ _ _ 12345 (sample
ID System ID)
Press [STO] EntrY and donE
Don't worry! If you make a mistake, trY AgAin will appear. After a few
seconds, your phone will display the incorrect number you entered for that
step. Press [CLR] to erase the last digit or press and hold [CLR] to
erase the entire entry. Re-enter the correct number, then press [STO] and
you're finished.
PRODUCT QUALITY IS YOURS WITH MOTOROLA
Long Programming
BEFORE YOU START!
Programming is normally done by a trained technician where the phone is
purchased. The following information must be obtained from the carrier
before programming can begin.
Customer cellular telephone number: (_ _ _) _ _ _ - _ _ _ _
Carrier System ID: _ _ _ _ _
Carrier Access Overload Class: _ _
Carrier Group ID: _ _
The battery must be charged to program a portable or personal phone. The
AC charger adapter is NOT sufficient to program or operate a phone with a
discharged battery. Mobiles must be connected to a power source.
Note: If a mistake is made, press [CLR] and re-enter data, or turn power
off to begin again.
Step 1. Press [PWR] to turn phone ON.
Press [FCN], 0 000000 000000 (13 zeros, or 0 + Factory preset
security code twice).
Note: You will not see any zeros in the display.
Press [RCL]; Display shows 01;
(If 00 appears in the display, you may have pressed the keys too
slowly or mis-entered the security code. Press [CLR] and try
again).
Step 2. Press [*]; Display shows 00000.
Enter Carrier System ID: _ _ _ _ _ .
Step 3. Press [*]; Display shows 02 (o2 2 when programming 2nd phone
number).
Press [*]; Display shows 111.
Enter Customer area code: _ _ _ .
Step 4. Press [*]; Display shows 03 (03 2 when programming 2nd phone
number).
Press [*]; Display shows 1 1 10 1 1 1.
Enter Customer phone number: _ _ _ - _ _ _ _ .
IMPORTANT: Verify phone number.
Step 5. Press [*]; Display shows 05 (05 2 when programming 2nd phone
number).
Press [*]; Display shows 00.
Enter Carrier Access Overload Class: _ _ .
Step 6. Press [*]; Display shows 06 (06 2 when programming 2nd phone
number).
Press [*]; Display shows 00.
Enter Carrier Group ID: _ _ .
STOP: At this point, select one of the following options:
If you wish to change the security code, unlock code, and /or
pursue programming options such as entering a second phone
number, go to Step 7.
If you are done programming, press [*], [SND]. This will save
your programming information and exit programming mode.
Step 7. Press [*]; Display shows 07.
Press [*]; Display shows 000000.
Enter desired six-digit security code, or go to Step 8. The
preset factory security code is 000000.
Note: Changing the security code is not advised. If it is
forgotten, the phone must be taken to an authorized
service center to be reset.
Step 8. Press [*]; Display shows 08.
Press [*]; Display shows 123.
Enter desired three-digit unlock code, or go to Step 9.
Step 9. Press [*], [*], [*]; Display shows 10.
Press [*]; Display shows a six-digit number containing only 0's
and 1's. Write your six-digit number here.
_____ _____ _____ _____ _____ _____
1st # 2nd # 3rd # 4th # 5th # 6th #
A. To disable handset internal speaker (disable speaker only
if your installation contains a separate external speaker/
VSP unit), write a "1" in the space below marked "1st".*
B. To program a second phone number, write a "1" in the space
below marked "5th".*
C. DO NOT change your 2nd, 3rd, 4th, or 6th numbers. Write
them below as shown in Step 9.
D. If you wish to make no changes, go to Step 10.
* For no change, write the default setting.
Step 10. Press [*]; Display shows 11.
Press [*]; Display shows a five-digit number containing only 0's
and 1's.
Write your five-digit number here:
_____ _____ _____ _____ _____
1st # 2nd # 3rd # 4th # 5th #
A. To turn Failed Page Indicator off, write a "1" in the space
below marked "1st".*
B. To disable the 8 hour Time-Out, write a "1" in the space
below marked "5th".*
C. DO NOT change the 2nd, 3rd, or 4th numbers. Write them
below as shown in Step 10.
D. If you wish to make no changes, go to Step 11.
* For no change, write the default setting.
Enter this Number: _____ _____ _____ _____ _____
1st # 2nd # 3rd # 4th # 5th #
Press [*], [SND].
If you have not selected to program a second telephone number,
programming is now complete. If you have selected to program a
second phone number, go to Step 11.
Step 11. Display shows 0 12.
Repeat Steps 2 - 6 from above using the information pertaining to
your 2nd carrier.
Press [*], [SND].
Programming is complete.
(5/27/99)